{"id":11360,"date":"2024-09-12T00:08:24","date_gmt":"2024-09-12T06:08:24","guid":{"rendered":"https:\/\/handandmachine.org\/classes\/computational_fabrication\/?p=11360"},"modified":"2024-09-12T02:08:19","modified_gmt":"2024-09-12T08:08:19","slug":"large-assignment-1-astrid","status":"publish","type":"post","link":"https:\/\/handandmachine.org\/classes\/computational_fabrication\/2024\/09\/12\/large-assignment-1-astrid\/","title":{"rendered":"Large Assignment 1- Astrid"},"content":{"rendered":"\n

Part 1: Curves<\/h2>\n\n\n\n

Open a new Rhino File and practice the curves commands by completing the following steps. Organize your Rhino file so each step is clear. Use the Text<\/strong> command to label each step and the commands you used.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n

Overall this was a simple process, with one minor misstep that started to add up: I use Adobe Illustrator on a daily basis for my job, so all the keyboard shortcuts are very strong in my muscle memory. I kept clicking keys that correspond to Illustrator shortcuts that were messing up my command in Rhino. After hours on Rhino I am finally starting to not default to these commands but it has really been a struggle!<\/p>\n\n\n\n

AstridLarson_Curves<\/a>Download<\/a><\/div>\n\n\n\n

Part 2: Surfaces<\/h2>\n\n\n\n

Open a new Rhino File and practice the surfaces commands below by making two different surfaces for each command. Organize your Rhino file so each step is clear. You may want to use some of the curves you modeled in Part 1. Use the Text<\/strong> command to label each step and the commands you used.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
AstridLarson_Surfaces<\/a>Download<\/a><\/div>\n\n\n\n

Part 3: Solids<\/h2>\n\n\n\n

Open a new Rhino File and practice the solids commands below by making two different solids for each command. You may want to use some of the curves and surfaces you modeled in Parts 1 and 2. Organize your Rhino file so each step is clear. Use the Text<\/strong> command to label each step and the commands you used.<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
AstridLarson_Solids<\/a>Download<\/a><\/div>\n\n\n\n

Part 4: 3D Printing<\/h3>\n\n\n\n